- 您现在的位置：买卖IC网 > Sheet目录988 > LM89EVAL (National Semiconductor)BOARD EVALUATION LM89
SNIS128C – AUGUST 2002 – REVISED MARCH 2013
Table 3. LOCAL and REMOTE TEMPERATURE REGISTERS (RTLB) (Read Only Address 10h):
BIT
Value
D7
0.5
D6
0.25
D5
0.125
D4
0
D3
0
D2
0
D1
0
D0
0
For RTLB D7–D5: Temperature Data. LSB = 0.125°C. Two's complement format.
The maximum value available from the Local Temperature register is 127; the minimum value available from the
Local Temperature register is -128. The maximum value available from the Remote Temperature register is
127.875; the minimum value available from the Remote Temperature registers is ? 128.875.
STATUS REGISTER (SR)
Table 4. STATUS REGISTER (SR) (Read Only Address 02h):
D7
Busy
D6
LHIGH
D5
LLOW
D4
RHIGH
D3
RLOW
D2
OPEN
D1
RCRIT
D0
LCRIT
Power up default is with all bits “0” (zero).
D0: LCRIT: When set to “1” indicates a Local Critical Temperature alarm.
D1: RCRIT: When set to “1” indicates a Remote Diode Critical Temperature alarm.
D2: OPEN: When set to “1” indicates a Remote Diode disconnect.
D3: RLOW: When set to “1” indicates a Remote Diode LOW Temperature alarm
D4: RHIGH: When set to “1” indicates a Remote Diode HIGH Temperature alarm.
D5: LLOW: When set to “1” indicates a Local LOW Temperature alarm.
D6: LHIGH: When set to “1” indicates a Local HIGH Temperature alarm.
D7: Busy: When set to “1” ADC is busy converting.
CONFIGURATION REGISTER
Table 5. CONFIGURATION REGISTER (Read Address 03h /Write Address 09h):
D7
ALERT mask
D6
RUN/STOP
D5
0
D4
Remote
D3
0
D2
Local
D1
0
D0
Fault Queue
T_CRIT_A
mask
T_CRIT_A
mask
Power up default is with all bits “0” (zero)
D7: ALERT mask: When set to “1” ALERT interrupts are masked.
D6: RUN/STOP: When set to “1” SHUTDOWN is enabled.
D5: is not defined and defaults to “0”.
D4: Remote T_CRIT mask: When set to “1” a diode temperature reading that exceeds T_CRIT setpoint will not
activate the T_CRIT_A pin.
D3: is not defined and defaults to “0”.
D2: Local T_CRIT mask: When set to “1” a Local temperature reading that exceeds T_CRIT setpoint will not
activate the T_CRIT_A pin.
D1: is not defined and defaults to “0”.
D0: Fault Queue: when set to “1” three consecutive remote temperature measurements outside the HIGH, LOW,
or T_CRIT setpoints will trigger an “Outside Limit” condition resulting in setting of status bits and associated
output pins..
18
Product Folder Links: LM89
Copyright ? 2002–2013, Texas Instruments Incorporated
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
LM95241EB
BOARD EVALUATION LM95241
LOB3R005FLFLT
RES METAL .005 OHM 3W 1% AXIAL
LP05-1A66-80V
RELAY REED SPST 500MA 5V
LP5521TMEV
EVAL BOARD FOR LP5521
LPS0300H1000JB
RESISTOR HEAT SINK 100 OHM 300W
LPS0600H4R70JB
RESISTOR HEAT SINK 4.7 OHM 600W
LPS0800H1000JB
RESISTOR HEAT SINK 100 OHM 800W
LPS1100H47R0JB
RESISTOR HEAT SINK 47 OHM 1100W
相关代理商/技术参数
LM8M.5M.5
制造商:Banner Engineering 功能描述:LM8M.5M.5 LOGIC MODULE
LM8M64
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN LCD Module
LM8M64_07
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN LCD Module
LM8V30
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN-LCD Module(Handheld PC)
LM8V302
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN-LCD Module(Handheld PC)
LM8V31
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN-LCD Module(Handheld PC)
LM8V311
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:DEVlCESPECIFICATIONfoor for Passive Matrix Color LCD Module (640 X 480 dots)
LM8V33
制造商:SHARP 制造商全称:Sharp Electrionic Components 功能描述:Color STN-LCD Module